Net Optics FX to TX Tap simplifies connecting 100Mbps copper monitoring and security devices to FX fiber network links. Convert FX to TX and tap into the link with one device, reducing cost and complexity at the same time. FX to TX Taps support passive monitoring at 100Mbps.

Transparent Access

FX to TX Taps establish permanent passive access ports without introducing a point of failure or disturbing other network connections. These passive Taps deliver full-duplex monitoring with zero impact on network traffic around the clock. Net Optics unique dust cap is tethered to the connector so it is always right where you need it.

Security and Visibility

Without an IP address, monitoring devices are isolated from the network, dramatically reducing their exposure to attacks. However, the monitoring device connected to the Tap still sees all full-duplex traffic as if it were in-line, including Layer 1 and Layer 2 errors.

Simply Plug It In

Full-duplex monitoring is a snap with supplied cables. All network and monitoring cables necessary for plug-and-play deployment are included with the Tap. Everything you need, right out of the box.

Reliability

For extra uptime protection, Net Optics FX to TX Taps offer redundant power connections. Should the primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of the Tap indicate the current power source – even if power is lost and reapplied, there is always zero delay to network traffic.

Splitter Specifications:
Split Ratio: 50:50
Network Port Insertion Loss:  4.5 dB Typical

Operating Specifications:
Operating Temperature: 0°C to 55°C
Relative Humidity: 10% min, 95% max, non condensing
Storeage Temperature: -10°C to 70°C

Mechanical Specifications:
Power Supply:
Input: 100-240VAC, 0.5A ~ 47 to 63 hz
Output: 5V 3.0 A
Dimensions: 1.0” high x 6.5” deep x 6.5” wide

Cable Interface:
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5/CAT5E
Link Distance Suuported: 100 meters
Fiber Link Length: 2km on 62.5µm Multimode Fiber, 5km on 8.5µm Singlemode Fiber

Connectors:
(2) RJ45, 8 pin connectors (100BaseTX monitor ports)
(2) duplex SC connectors (100BaseFX network ports)

Certifications:
Fully RoHS compliant

Part Numbers:
CVT-MM5/CU
CVT-MM4/CU
CVT/MM3/CU
CVT-SM5/CU
CVT-SM4/CU
CVT-SM3/CU

Passive, Secure Technology

 

Provides passive access at 100 Mbps without data stream interference or introducing a point of failure

Access fiber links with copper devices without a separate converter

Permanent in-line installation without affecting network performance

Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting

No IP address is needed for the Tap or monitoring device, enhancing monitoring security

Redundant power ensures monitoring uptime

Fully IEEE 802.3 compliant

Fully RoHS compliant

Warranty

 

All Net Optics products come standard with a 1 year manufacturer's warranty

Optional 1 or 2 year extended warranty available at time of product purchase

 

Ease of Use

LED indicators show redundant power and link status

Front-mounted connectors make installation and operation quick and easy

Silk-screened application diagram illustrates all connections for easy deployment

All network and monitoring cables included

Optional 19-inch rack frames hold up to 2 Taps

Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems

Part Numbers

Multimode FX to TX Tap

1. -CVT-MM5/CU
     Converter Tap, Fiber(1300nm) to 
     Copper(10/100), MM 62.5µm,
     50:50 split ratio
   - CVT-MM4/CU
     Converter Tap, Fiber(1300nm) to 
     Copper(10/100), MM 62.5µm,
     60:40 split ratio
   - CVT/MM3/CU
     Converter Tap, Fiber(1300nm) to 
     Copper(10/100), MM 62.5µm,
     70:30 split ratio
   
   - RK-2
     2-Slot Rack Mount Frame
   

Singlemode FX to TX Tap   

- CVT-SM5/CU

  Converter Tap, Fiber(1310nm) to

  Copper(10/100), SM 8.5µm,

  50:50 split ratio

- CVT-SM4/CU

  Converter Tap, Fiber(1310nm) to

  Copper(10/100), SM 8.5µm,

  60:40 split ratio

- CVT-SM3/CU

  Converter Tap, Fiber(1310nm) to

  Copper(10/100), SM 8.5µm,

  60:40 split ratio

Net Optics - manufacturer of iTap™ - 10/100/1000 - GigaBit Network Taps, 10/100 - GigaBit Aggregator Taps, TX-SX, LX-SX All Converter Taps, IPS & IDS Bypass Switches, Matrix Switches and Teeny Tap™.

Resources

For more information, pricing, demonstration or evaluation on Net Optics Products please contact us here.

Questions? Call  1-805-277-2400