NextGig Systems, Inc. - Network Connectivity & Test Solutions
NextGig Systems, Inc. - Network Connectivity & Test Solutions
Net Optics 8x1 10/100 Active Response Regeneration Tap
Net Optics 8x1 10/100 Active Response Regeneration Taps solve the key physical layer challenges of multi-device monitoring and response. Active response capability increases Tap-based monitoring flexibility and efficiency. For a complete picture of network health, these Taps connect up to eight different network management and security devices at any single network location.
One Tap, No Idle Resources
Keep your intrusion detection and prevention systems, protocol analyzers, RMON probes, and other security devices productive with a single Regeneration Tap. Maximize resources and save on access points when multiple devices can monitor link traffic simultaneously through a single Regeneration Tap. Secure, passive access for multiple devices simply means a better return on monitoring investments.
Response Ready
When active responses to network events are required, the last monitoring port can be changed to an Active Response Port using a hardware switch. The Active Response Port now becomes bi-directional allowing it to buffer and transmit into the network link any type of Ethernet packet, from a simple TCP reset to ICMP messages. The optional Active Response Port can be easily switched back to passive monitoring via the hardware switch. The combination of active response capability and passive monitoring in the Tap reduces the number of devices and network ports required for active response functionality.
Reliability
For extra uptime protection, Net Optics Taps offer redundant power connections. Should the primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of the Tap indicate the current power source.
Frequently Asked Questions
Q: What types of active responses are supported?
A: With an Active Response Regeneration Tap, an administrator can transmit any type of Ethernet packet back into the original link, supporting all common types of active responses generated by intrusion detection systems, and by intrusion prevention systems deployed in passive mode. The most common response types are TCP resets, and firewall rule changes. While the Tap can support both types of responses, we advocate extreme caution in dynamically updating firewall rules, due to the risk of disabling network services. Because most firewalls are managed out-of-band, however, it is unlikely that the Regeneration Tap would be part of a rule change scenario.
Q: How are collisions avoided when active responses are transmitted back into the original link?
A: On each side of the full-duplex link, there is a small buffer for traffic arriving from the network, and another small buffer for active response traffic arriving from the monitoring device. Traffic is released from this buffer pair on a first-in, first-out basis. If both sides of the buffer are empty and a packet originating from the monitoring device and a packet originating from the network arrive at the same time, priority is given to the network packet.
Q: How much bandwidth is available on the Active Response Port?
A: The average amount of bandwidth for active responses is determined by the average available capacity on the link. For example, on a 100 Mbps full-duplex link, if transmission from device A to device B averages 30 Mbps, and transmission from device B to device A averages 50 Mbps, then there is average capacity on the first side for 70 Mbps, and on the second side for up to 50 Mbps of active response traffic.
At any particular point in time, actual capacity is determined by the size of the packets being transmitted, and the gap between these packets. On a standard link with 64-byte network and active response traffic, the capacity at any point in time will be very close to the average capacity. (We do not recommend using the Tap on links with jumbo packets as these large – up to 9K – packets can fill the buffer and impact performance.)
As the most common use for the Tap will be to inject TCP resets, which are standard 64-byte packets, it is unlikely that the transmissions from either side of the Active Response Port will exceed 10 Mbps, even if many sessions are terminated in a short time frame. Pending available capacity, we recommend the use of the Active Response Port at speeds up to 10 percent of link bandwidth, which is 10 Mbps on a 100 Mbps link.
Q: Does the Active Response Port require the connected monitoring device to have an IP address?
A: Yes, the connected monitoring device is required to have a MAC and IP address when the Active Response Port is operating in active mode. These are not required when this Port is set to passive mode. The Tap itself never has a MAC or IP address, regardless of how the Active Response Port is set.
Operating Specifications:
Operating Temperature: 0°C to 55°C
Storage Temperature: -10°C to 70°C
Relative Humidity: 10% min, 95% max, non-condensing
Mechanical Specifications:
Redundant Power Supplies: 100-240VAC, 0.5A, 47-63Hz
Dimensions: 1.75" high x 10.5” deep x 17” wide
Connectors:
(14) RJ45 Connectors (Passive Monitoring Ports)
(2) RJ45 Connectors (Passive Monitoring/Active Response Ports)
(2) RJ45 Connectors (Network Ports)
Cable Interface:
Copper Cable Type: 22-24 AWG Unshielded twisted pair cable, CAT5/CAT5E
Link Distance Supported: 100 meters
Certifications:
Fully RoHS compliant
Part Number:
RGN-CU-AR-IL8
Passive, Secure Technology
Enables real-time, simultaneous full-duplex monitoring of eight 10/100 link with two monitoring devices
Provides complete full-duplex visibility at 10 or 100 Mbps without data stream interference or introducing a point of failure
Passes all traffic (including errors) from all network layers for comprehensive troubleshooting
Redundant power ensures monitoring uptime
Fully IEEE 802.3 compliant
Fully RoHS compliant
Warranty
All Net Optics products come standard with a 1 year manufacturer's warranty
Optional 1 or 2 year extended warranty available at time of product purchase
Enhanced, Efficient Monitoring
Active response capability increases Tap-based monitoring flexibility and efficiency
Hardware switch provides a secure transition between passive mode (transmit only) and active mode (transmit/receive) for the
Active Response Port
Ease of Use
LED indicators show redundant power, speed, link, and activity status.
DIP switches select auto-negotiation or fixed speed and duplexing settings for the Tap
Front-mounted connectors support easy installation and operation
Silk-screened application diagram illustrates all connections for easy deployment
Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems
Part Numbers
8x1 10/100 Active Response
Regeneration Tap
- RGN-CU-AR-IL8
Regen, 8x1, IL, Copper, 10/100,
Active Response
Net Optics - manufacturer of iTap™ - 10/100/1000 - GigaBit Network Taps, 10/100 - GigaBit Aggregator Taps, TX-SX, LX-SX All Converter Taps, IPS & IDS Bypass Switches, Matrix Switches and Teeny Tap™.
Resources
For more information, pricing, demonstration or evaluation on Net Optics Products please contact us here.
Questions? Call 1-805-277-2400
All registered and unregistered trademarks are the sole property of their respective owners.
Copyright © NextGig Systems, Inc. All Rights Reserved.
Products | Solutions | Store | Support | News | About Us | Why NextGig? | Employment | Privacy | Sitemap | Contact Us