NextGig Systems, Inc. - Network Connectivity & Test Solutions
NextGig Systems, Inc. - Network Connectivity & Test Solutions
Net Optics 10/100 Active Response Dual Port Aggregator Tap
Net Optics Active Response Dual Port Aggregator Taps provide ultra-efficient access to critical links with the option to inject an active response into the network. This pioneering technology enables any two devices to simultaneously monitor a full-duplex link - using only one NIC per device.
Typically, full-duplex monitoring with a network tap requires two NICs (or a dual channel NIC) – one interface for each side of the tapped full-duplex connection. The Dual Port Aggregator Tap combines and regenerates these streams, sending all aggregated data out two separate passive monitoring ports. The best part of this innovation is the onboard memory to make sure traffic isn’t dropped during bursts.
Response Ready
When active responses to network events are required, the first monitoring port can be changed to an Active Response Port using a hardware switch. The Active Response Port buffers and transmits into the network link any type of Ethernet packet, from a simple TCP reset to ICMP messages. The Active Response Port can be easily switched back to passive monitoring via the hardware switch.
The combination of active response capability and passive monitoring in the Tap reduces the number of devices and network ports required for active response functionality.
Buffering Prevents Lost Data
The Active Response Dual Port Aggregator Tap is designed to handle the combined traffic of a single full-duplex link. Normally, the traffic should be below the receiving capacity of the NIC, that is, less than 10 or 100 Mbps.
When the traffic queue exceeds the capacity of the NIC, the Tap buffers the overflow of up to one megabyte per side of the full-duplex connection. For your convenience, the buffers clear automatically when the traffic volume falls below the receiving capacity of the NIC. For example, if there is a traffic burst and a tap connected to a 100 Mbps network port on a monitoring device is now receiving 140 Mbps of traffic, the Tap buffers data until the burst is over. The Tap then sends the buffered data to the monitoring device until the buffer is cleared.
Simple to Deploy
Net Optics’ Active Response Dual Port Aggregator Tap is a simple plug-and-play solution addressing the fact that many monitoring systems, including most software based solutions, only offer a single channel NIC, limiting full-duplex visibility. While adding a second NIC can help maintain data integrity and visibility, there is a tradeoff in flexibility and ease-of-use. An operating system and NICs that enable binding are often required to achieve the same functionality as the Dual Port Aggregator Tap. In contrast, the Dual Port Aggregator Tap requires no additional components or configuration on the monitoring devices.
Better than Span Ports
In the past, span ports were occasionally used to aggregate tapped traffic. However, in addition to other shortcomings of span port monitoring, span ports support very limited buffering and can simply drop data during bursts. The generous buffers of the Dual Port Aggregator Tap prevent data loss in these conditions.
Security and Visibility
Without an IP address, monitoring devices are isolated from the network, dramatically reducing their exposure to attacks. However, the monitoring device connected to the Tap still sees all full-duplex traffic as if it were in-line, including Layer 1 and Layer 2 errors.
Simply Plug It In
Full-dulpex monitoring to a single NIC is a snap with the Aggregator Tap. All network and monitoring cables necessary for plug-and-play deployment are included with the Tap. Everything you need, right out of the box.
Reliability
For extra uptime protection, Net Optics Taps offer redundant power connections. Should the primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of the Tap indicate the current power source – even if power is lost and reapplied, there is always zero delay to network traffic.
Operating Specifications:
Operating Temperature: 0°C to 55°C
Storage Temperature: Relative Humidity: 10% min, 95% max, non condensing
Mechanical Specifications:
Power Supply:
Input: 100-240 VAC, 0.5A ~ 47-63Hz
Output: 12V, 1.5A
Dimensions: 1.125" high x 9.125" deep x 4.5" wide
Cable Interface:
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5/CAT5E
Link Distance Supported: 100 meters
Connectors:
(2) RJ45, 8 pin connectors (network ports)
(1) RJ45, 8 pin connector (passive monitor port)
(1) RJ45, 8 pin connector (active/passive monitor port)
Certifications:
Fully RoHS compliant
Part Number:
PAD-CU-AR
Passive, Secure Technology
Supports full-duplex monitoring with a single NIC, increasing monitoring efficiency
Regeneration Tap technology enables two devices to simultaneously monitor all aggregated traffic – using only one NIC per device
One megabyte of memory for each side of the full-duplex link (two megabytes memory, total) prevents data loss during excessive traffic loads
Provides complete full-duplex visibility at 10 or 100 Mbps without data stream interference or introducing a point of failure
Compatible with Mid-Span Power over Ethernet (PoE) applications
Passes all traffic (including errors) from all layers for comprehensive troubleshooting
No IP address is needed for the Tap or monitoring device, enhancing monitoring security
Redundant power ensures monitoring uptime
Enhanced, Efficient Monitoring
Active response capability increases Tap-based monitoring flexibility and efficiency
Hardware switch provides a secure transition between passive mode (transmit only) and active mode (transmit/receive) for the Active Response Port
Fully RoHS compliant
Warranty
All Net Optics products come standard with a 1 year manufacturer's warranty
Optional 1 or 2 year extended warranty available at time of product purchase
Ease of Use
LED indicators show redundant power, speed, link, and activity status
DIP switches select auto-negotiation or fixed speed and duplexing settings for the Tap
Front-mounted connectors support easy installation and operation
Silk-screened application diagram illustrates all connections for easy deployment
All network and monitoring cables included
Optional 19-inch rack frames hold up to three Taps
Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems
Part Numbers
10/100 Active Response
Dual Port Aggregator Tap
- PAD-CU-AR
Port Agg, Copper, 10/100, Active Response
- RK-3V2
Rack Panel Frame, 3-Slot 19"
- RK-12V2
Rack Panel Frame, 12-Slot 19"
Net Optics - manufacturer of iTap™ - 10/100/1000 - GigaBit Network Taps, 10/100 - GigaBit Aggregator Taps, TX-SX, LX-SX All Converter Taps, IPS & IDS Bypass Switches, Matrix Switches and Teeny Tap™.
Resources
For more information, pricing, demonstration or evaluation on Net Optics Products please contact us here.
Aggregator Taps
Connectivity
Bypass Switches
Indigo Pro
Related Products
All Network Taps
Aggregation Switches
Network Monitoring
Network Recording
Ethernet Testing
Network Emulation
Network Cables
Storage Emulation
Questions? Call 1-805-277-2400
All registered and unregistered trademarks are the sole property of their respective owners.
Products | Solutions | Store | Support | News | About Us | Why NextGig? | Employment | Privacy | Sitemap | Contact Us
Copyright © NextGig Systems, Inc. All Rights Reserved.